2610 TECHNICAL SPECIFICATIONS

General
2-Site Model

Operating Voltage: 100-240 VAC
Frequency: 50-60 Hz
Current Rating: 8-4 A (Fuse 250V 6A SB)
Dimensions and Mass: 21.55” (547mm) x 8.65” (220mm) x 4.68” (119mm), 12.2 lbs. (5.5 kg)

4-Site Model
Operating Voltage: 100-240 VAC
Frequency: 50-60 Hz
Current Rating: 10-5 A (Fuse 250V 6A SB)
Dimensions and Mass: 21.55” (547mm) x 16.10” (409mm) x 4.68” (119mm), 21.5 lbs. (9.6 kg)

6-Site Model
Operating Voltage: 100-240 VAC
Frequency: 50-60 Hz
Current Rating: 12-6 A (Fuse 250V 6A SB)
Dimensions and Mass: 31.35” (796mm) x 16.10” (409mm) x 4.68” (119mm), 31.5 lbs. (14.3 kg)

Software
Required: BPWin
File Type: binary, Intel, JEDEC, Motorola, POF, RAM, straight hex, hex-space, Tekhex, Extended Tekhex, ASCII hex, Formatted Binary (.DIO), AFM, OMF, LOF, MER, and others Device Commands: blank, check
sum, compare, options, program, test, verify
Features: data editor, revision history, session logging, on-line help, device and algorithm information

Hardware
Architecture: Concurrent Programming System
Sites: 2, 4, or 6 per chassis; multiple chassis may be linked
Calibration: annual, may be performed on site
Diagnostics: pin continuity test, RAM, ROM, CPU, pin drivers, power supply, communications, cables, calibration, timing, ADC, DAC, interconnects
Memory: 64MB per site standard
User Interface: Pass, Fail, Active, Start LEDs and Start witch on each site; PC display shows systems status at a glance; auto-start mode automatically begins programming when device is inserted
PC System Requirements: Microsoft Windows 2000 or above

Standard Accessories Included
software on CD-ROM
user manual on CD-ROM
power cable
data cable
1-year hardware warranty
1-year software support

PIN Drivers
Quantity: 240-pins standard
Analog Slew rate: 0.3 to 25V/µs
Vpp Range: 0-25V
Ipp Range: 0-70mA continuous, 250mA peak
Vcc Range: 0-12V
Icc Range: 0-1A
Very low voltage: to 1.5V (Vdd)
Rise Time: 4ns
Overshoot: none
Clocks: continuously variable 1 MHz to 30 MHz
Protection: overcurrent shutdown, power failure shutdown
Independence: pin drivers and waveform generators are fully independent and concurrent on each site

Features
File Loading: automatic file type identification; no download time because programmer is PC controlled; supports Intel, JEDEC, Motorola S-record, POF, straight hex, hex-space, Tekhex, and other file formats
Device Selection: intelligent device selector allows you to type as little or as much of the part number as you like then choose from a list of devices matching your description
Devices Supported: including, but not limited to, Antifuse, Low Voltage, PROM, EPROM, EEPROM, Flash EEPROM, Microcontrollers, SPLD, CPLD, FPGA
Continuity Test: each pin, including Vcc, ground, and signal pins, may be tested before every programming operation
Protection: overcurrent shutdown; power failure shutdown; ESD protection, reverse insertion, banana jack for ESD wrist straps
Options: available Socket Modules including, but not limited to, Universal PLCC, standard PLCC, PGA, CSP, BGA, µBGA, SOIC, QFP, TSOP, LCC, SDIP, PCMCIA, SIMM—JobMaster™ software, and Advanced Feature Software
Programming Yield: assured by independent universal pin drivers on each socket, short distance from pin drivers to device, and accuracy of waveforms
Algorithms: all algorithms are manufacturer approved or certified (if required)—BPM Microsystems has an excellent record of being first to provide certified algorithms for new devices
Algorithm Updates: algorithm changes and updates are available, additional algorithms available by subscription after the first year